{"id":6603,"date":"2026-11-18T23:06:22","date_gmt":"2026-11-18T15:06:22","guid":{"rendered":"https:\/\/www.chengtop1.com\/products\/die-cut-label-corners-radius-edge-lift\/"},"modified":"2026-11-18T23:06:22","modified_gmt":"2026-11-18T15:06:22","slug":"die-cut-label-corners-radius-edge-lift","status":"publish","type":"cxb_products","link":"https:\/\/www.chengtop1.com\/fr\/products\/die-cut-label-corners-radius-edge-lift\/","title":{"rendered":"Die-Cut Label Corners: Radius and Edge Lift"},"content":{"rendered":"<p>A label with sharp square corners tends to fail at one of those corners. A sleeve, a shipping carton or a finger catches the point, the facestock lifts a millimetre, and the lift spreads along the edge over the next few days. A rounded corner radius is a small change on the die drawing that removes the starting point.<\/p>\n<h2>Why a Corner Starts the Lift<\/h2>\n<p>Adhesive holds a label across its area, and the outside edge has the least support. A square corner concentrates any sideways rub into one point, while a radius spreads it along a curve. The effect is stronger on a thin film facestock, which has a little spring of its own and wants to return to flat once a corner is raised.<\/p>\n<p>The carton surface matters as much as the label. A soft-touch film, a textured uncoated board and a recycled kraft sheet give the adhesive less to grip than a smooth coated surface. Where the finish is unusual, a slightly larger radius and a more tolerant adhesive keep the edge down.<\/p>\n<h2>Choosing a Radius That Fits the Artwork<\/h2>\n<p>A radius of a few millimetres is enough on a small label, and a larger one reads as a deliberate shape on a big panel. Set it from the artwork: a circular seal wants a true circle, a rectangular shade label wants a modest corner radius, and a border that runs close to the edge needs enough room that the radius does not cut into it. Keep the border and the die on one file so a late artwork change does not leave the two out of step.<\/p>\n<p>Where the label crosses a carton crease, no radius will hold the edge down. Move the label to a flat panel or split it into two pieces, one on each face.<\/p>\n<h2>Die Quality and Cutting Waste<\/h2>\n<p>A worn die leaves a ragged edge that lifts as readily as a square corner. A clean cut through the facestock without scoring the liner keeps the label flat on release and lets it peel cleanly. Where the run is long, plan a die check partway through so a dull tool does not quietly change the edge quality. The <a href=\"https:\/\/www.chengtop1.com\/fr\/categorie-de-produits\/stickers-labels\/\">autocollants et \u00e9tiquettes<\/a> range covers paper and film constructions, and the <a href=\"https:\/\/www.chengtop1.com\/fr\/categorie-de-produits\/boites-de-cosmetiques\/\">bo\u00eetes de cosm\u00e9tiques<\/a> range includes soft-touch surfaces that need a little extra edge tolerance.<\/p>\n<h2>Testing Against Real Handling<\/h2>\n<p>Rub an applied label along a carton edge, then pack a few cartons into a shipping outer and leave them for a day. Look at the corners under raking light: a lift that starts as a bright line is easy to miss under flat overhead lighting. Check a label from the end of the run as well as one from the start.<\/p>\n<h2>Checks Before the Die Is Cut<\/h2>\n<ul>\n<li>Set the corner radius from the artwork border, with both on one file.<\/li>\n<li>Confirm the die cuts the facestock without scoring the release liner.<\/li>\n<li>Keep the label off carton creases and folds.<\/li>\n<li>Rub an applied label along a carton edge and inspect it a day later.<\/li>\n<li>Compare edge quality on labels from the start and the end of a long run.<\/li>\n<\/ul>\n<p>Label shape also affects how a label is picked up. A long narrow label bends in the hand and can be laid down with a small twist, which leaves one corner standing proud. Where the artwork allows, a slightly squarer proportion goes on straighter and gives the adhesive less edge to defend at the corners.<\/p>\n<p>Send the label size, the facestock and the carton finish when you ask for a quote. With the radius, the die condition and the surface settled together, the label stays flat through packing and arrives without a lifted corner.<\/p>","protected":false},"excerpt":{"rendered":"<p>Sharp square corners catch on a sleeve or a shipping carton and start an edge lift that spreads across the label. A rounded radius holds better, particularly on a soft-touch or textured carton where the adhesive has less to grip. Set the radius with the artwork in mind, and rub a sample label along a carton edge before approving the die.<\/p>","protected":false},"featured_media":6555,"menu_order":0,"template":"","cxb_product_category":[30],"cxb_product_tag":[],"class_list":["post-6603","cxb_products","type-cxb_products","status-publish","has-post-thumbnail","hentry","cxb_product_category-stickers-labels"],"_links":{"self":[{"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/cxb_products\/6603","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/cxb_products"}],"about":[{"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/types\/cxb_products"}],"version-history":[{"count":0,"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/cxb_products\/6603\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/media\/6555"}],"wp:attachment":[{"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/media?parent=6603"}],"wp:term":[{"taxonomy":"cxb_product_category","embeddable":true,"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/cxb_product_category?post=6603"},{"taxonomy":"cxb_product_tag","embeddable":true,"href":"https:\/\/www.chengtop1.com\/fr\/wp-json\/wp\/v2\/cxb_product_tag?post=6603"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}