Two cartons arrive from the same supplier and one is rejected by the filling line while the other runs cleanly. The difference turns out to be a glue flap half a millimetre short, which is inside the tolerance the factory applies and outside the tolerance the filling machine needs. No document says which tolerance governs, so the argument runs until someone agrees to absorb the cost. A packaging specification sheet exists to prevent exactly that conversation.
What the sheet is for. It is the document that defines the pack in dimensions a factory can measure, materials a mill can certify and processes a converter can control. It is not a design brief and not a purchase order. When it is written well, it removes the ambiguity that a drawing alone leaves, because a drawing shows shape while a specification states what variation is acceptable.
The dimensional block. Overall length, width and depth, with a stated tolerance for each, and a note on which dimension the tolerance applies to after folding rather than flat. Internal dimensions matter as much as external for a product that has to fit, and for a mailer or a shipper the internal dimension is the one that governs. Die line dimensions should reference the actual tooling, with a revision number, because a die that has been re-cut is not the same die, and the print run length determines how often that happens. Crease positions, glue flap width and panel sequence belong here too, with a tolerance for crease placement that reflects what the folder-gluer can hold.
The material block. Board grade by name and by measured calliper, with a tolerance range, plus the mill and the certificate if the buyer requires chain of custody. Flute type for corrugated, with a note on the take-up factor if stacking strength has been calculated. Liner grades for a printed corrugated pack. For a rigid box, the greyboard thickness, the wrap paper weight and the lining material. Naming the grade without a calliper range is a common gap: two boards with the same trade name can differ enough to change how a carton folds.
The print block. Number of colours, the ink system by type, the reference standard for colour approval, and the tolerance in a measurable form. Coverage or ink weight per area if the buyer is tracking cost. Varnish or lamination by type and coverage, including whether it goes over the glue areas, because a varnish in the wrong place causes a bond failure that shows up weeks later. For a brand colour, a physical reference and a measured target, with a light source named, so that two sites can reach the same decision.
The finishing and assembly block. Die cutting, creasing, window patching with the film type and thickness, foil or embossing with the die reference, gluing pattern with the adhesive type, and for hand-assembled boxes the assembly method and the adhesive. Packing instructions belong here as well: count per inner, count per shipper, orientation, and any divider or insert. A specification that stops at the printing stage leaves the last two operations to be agreed by email, which is where packing errors start.
Tolerances that a factory can actually check. A tolerance is useful when it can be measured with equipment on the factory floor at production speed. A tolerance of plus or minus 0.3 millimetres on a folded dimension is checkable with a calliper or a go-no-go gauge; a tolerance of plus or minus 0.1 is not, on a folding carton, and writing it only creates disputes. The same logic applies to colour: a measured Delta E target with a stated light source is checkable, while the instruction to match a sample is not. Writing checkable tolerances is the single largest improvement a specification sheet needs.
The acceptance and inspection block. What sample size is inspected, at what AQL, which defects are critical, major and minor, and what happens when a lot fails. Referencing a recognised inspection standard rather than describing defects in prose makes the clause enforceable. For printed packaging, adding a limit sample for colour and a physical reference for crease quality does more than another paragraph of description. The acceptance criteria need to be agreed before the first production run, not after the first rejection.
Revision control. A specification sheet without a revision number and a change log becomes unreliable within a year, because two buyers will hold two versions and a factory will work from a third. Each change should carry a date, an owner and a note on what it affects, and old versions should be archived rather than edited. Where a change affects the die or the plates, the sheet should reference the artwork revision as well, so a reprint cannot be produced from a superseded file. Buyers who have been through one artwork mix-up usually add this section first.
How it connects to the quote. A specification issued before the quote produces comparable prices, because each supplier prices the same construction. A specification issued after the quote produces a price that has to be renegotiated, and a supplier who has already committed to a number will recover the difference elsewhere, often in board grade or packing. Sending a one-page specification with the enquiry is the lowest-cost quality improvement available, and it makes the RFQ shorter for everyone.
Where a specification sheet fails. The failures are consistent: dimensions without tolerances, material named without a calliper, colour described rather than measured, no statement of which surface is printed, and no packing instruction. Each of those gaps becomes a dispute later, and the cost of the dispute usually exceeds the time it would have taken to write the line. A sheet does not need to be long. Two pages with the right fields beats ten pages of description.
If your current specification is a drawing and an email trail, we can work from it and send back a structured version with tolerances and an inspection clause for your review. Send the drawing, the board grade and one photo of a good carton, and we will show you what the sheet should contain.


